• High temperature automotive adjustable voltage regulator
• Input voltage from 4.5V to 30V with input transient (load dump) of up to 35V
• Output voltage of 3.0V to 28V
• Chip-enable input signal allowing to put the IC into low-power disable mode
• Output voltage accuracy of ±5% (excluding accuracy of exernal components but including accuracy, temperature, line and load regulation variations)
• Temperature range of -55°C to 175°C
• Typical quiescent current of 1.1mA
• Miniature 8-pin PSOIC8 package with exposed pad
• AEC-Q100 Grade 0 & PPAP capable (full qualification pending, please contact us for current status)

Typical Applications for the CXT-STA4919 from Cissoid include:

• Regulated power supplies for embedded electronics in automotive and industrial systems
• High-temperature automotive applications

The below table gives the full specifications of the Cissoid CXT-STA4919 voltage regulator:

Unless otherwise stated, T_j= 25°C,C_in= 4.7µF, C_out= 4.7µF. Bold figures point out values valid over the whole temperature range (T_j= -55°C to +175°C)

⁸ Please refer to Figure 11 on the datasheet (available in Technical Library) for evolution of minimum dropout in function of required output current

⁹ Load regulation measurements must be done in a way to avoid self-heating effect

¹⁰ Current through feedback resistances excluded

¹¹ Based on FR4 2s2p board + thermal vias under the exposed pad

The post Cissoid CXT-STA4919 appeared first on Rhopoint Components.

• High temperature, negative low-dropout linear voltage regulator
• Voltage reference values of -2.5V, -3.3V, -5V, -5.5V, -9V, -10V, -12V, -13V and -15V
• Dropout voltage of -2V down to -20V
• Output voltage programmable by bonding option (bare die version)
• Quiescent current consumption of 3mA
• Maximum output current of 1A at 225°C (For -2.5V version, max current is 100mA)
• Total accuracy of ±3%
• Typical operating temperature range −55°C to +225°C (operational up to 300°C)
• Maximum drift with temperature 80ppm
• Validated at +225°C for 43800 hours (and still on-going)
• Available in TO-254 package and bare die available on request

Typical Applications for the CHT-LDNS series from Cissoid include:

• Well logging
• Automotive
• Aeronautics
• Aerospace

The below table gives the full specifications of the Cissoid CHT-LDNS series:

1.|Vin| max=30V2. For -2.5V version, max current is 100mA3. Above +225°C (T_j), a minimum load current of few mA could be required

4. Max power dissipation depends on packaging

5. ppm are defined as [d(Vout)/d(T)]/Vout. For -15V mode, 40ppm corresponds to 600µV/°C

6. Defining “x” as the nominal voltage, the line regulation is better than x/5 mV/V for|Vin|>14V and better than x mV/V for |Vin|≤14V. For 2.5V output voltage version, line regulation is better than 8mV/V for |Vin|>14V and better than 3mV/V for |Vin|≤14V

7. This includes the packaging parasitic resistor

8. Defining “x” as the nominal voltage, the typical quiescent current at 2V dropout can be approximated as 2.95+x/13 in mA @ -55°C and 2.65+x/13 in mA at 225°C

9. Defining “x” as the nominal voltage, the minimum power supply rejection ratio is …(tbd)…

10 Defining “x” as the nominal voltage, typical noise level is …(tbd)…

11. short circuit current for 2.5V typical is 1A and max is 1.3A

 

The post Cissoid CHT-LDNS Series appeared first on Rhopoint Components.

• High temperature voltage reference
• Voltage reference values of 2.5V, 3.3V, 5V, 9V, 10V and 12V
• Dropout voltage at 1mA is 1.5V to 15V (CHT-BG3M-025 min dropout is 2V)
• Dropout voltage at 3mA is 2.5V to 15V (CHT-BG3M-025 min dropout is 3V)
• Quiescent current consumption of 700µA
• Maximum output current of 3mA at 225°C
• Total accuracy of ±2%
• Typical operating temperature range −55°C to +225°C
• Maximum drift with temperature 70ppm
• Validated at +225°C for 30000 hours (and still on-going)
• Available in TO-39 package (other packages available on request)

Typical Applications for the CHT-BG3M series from Cissoid include:

• Well logging
• Automotive
• Aeronautics
• Aerospace

The below table gives the full specifications of the Cissoid CHT-BG3M series:

1. For CHT-BG3M-025, min dropout is 2V at 1mA and 3V at 3mA

2. Input voltage cannot exceed 25V

3. ppm are defined as [d(Vout)/d(T)]/Vout. For 5V mode, 70ppm corresponds to 350µV/°C

4. Defining “x” as the nominal voltage, the line regulation is better than x/5 mV/V

5. Defining “x” as the nominal voltage, the minimum power supply rejection ratio is 66-1.2x.db

6. Defining “x” as the nominal voltage, typical noise level is (x/5)*240µVRMS

The post Cissoid CHT-BG3M Series appeared first on Rhopoint Components.

• High temperature, low-dropout linear voltage regulator
• Voltage reference values of 2.5V, 3.3V, 5V, 5.5V, 5.6V, 7.5V, 9V, 10V, 12V, 13V and 15V
• Dropout voltage of 1V to 20V at lower than 400mA
• Dropout voltage of 2V to 20V at 1A
• Quiescent current consumption of 3mA
• Maximum output current of 1A at 225°C
• Total accuracy of ±2%
• Typical operating temperature range −55°C to +225°C (operational up to 300°C)
• Maximum drift with temperature 80ppm
• Validated at +225°C for 43800 hours (and still on-going)
• Available in TO-254 package and bare die available on request

Typical Applications for the CHT-LDOP series from Cissoid include:

• Well logging
• Automotive
• Aeronautics
• Aerospace

The below table gives the full specifications of the Cissoid CHT-LDOP series:

1. The maximum input voltage V_in is V_out +20V or 30V, whichever is less

2. Above +225°C (T_j), a minimum load current of few mA could be required

3. Max power dissipation depends on packaging

4. ppm are defined as 1e-6x[d(Vout)/d(T)]/Vout. For a nominal output of 15V, 40ppm corresponds to 600µV/°C

5. Defining “x” as the nominal voltage, the line regulation is better than x/5 mV/V

6. This includes the packaging parasitic resistance for TO-254 packages

7. Defining “x” as the nominal voltage, the typical quiescent current at 2V dropout can be approximated as 2.95+x/13 in mA @ -55°C and 2.65+x/13 in mA at 225°C

8. Preliminary data

 

The post Cissoid CHT-LDOP Series appeared first on Rhopoint Components.

• Surface-mount high voltage, low power voltage regulator
• Input voltage range from 4.5V to 36v
• Regulated output Voltage between 3V and 3.6V
• Regulated output current 0.02A
• Reverse battery protection of -60V
• Excellent immunity to transients and ESD
• Temperature range from -40°C to +170°C
• Small, low profile TDFN6 package

The NVE DC001-10E high voltage, low power voltage regulators are ideal for the following applications:

• Industrial Sensors
• Industrial Controls
• Automotive Sensors
• Automotive Controls

The below table gives the full specifications of the NVE DC series including the DC001-10E

The post NVE DC001-10E appeared first on Rhopoint Components.

• Surface-mount high voltage, low power voltage regulator
• Input voltage range from 6.2V to 36v
• Regulated output Voltage between 4.5V and 5.5V
• Regulated output current 0.02A
• Reverse battery protection of -60V
• Excellent immunity to transients and ESD
• Temperature range from -40°C to +170°C
• Small, low profile TDFN6 package

The NVE DC002-10E high voltage, low power voltage regulators are ideal for the following applications:

• Industrial Sensors
• Industrial Controls
• Automotive Sensors
• Automotive Controls

The below table gives the full specifications of the NVE DC series including the DC002-10E

The post NVE DC002-10E appeared first on Rhopoint Components.