Non-Magnetic Resistors - Rhopoint Components

SRT CRB 1216H-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1216H-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 1216H range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.4W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 8/single cut), all in a small 1216 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1216H-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1216 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.4W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 8/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1216H-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1216H-HT appeared first on Rhopoint Components.

SRT CRB 1216-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1216-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 1216 range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.4W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 4/single cut), all in a small 1216 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1216-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1216 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.4W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 4/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1216-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1216-HT appeared first on Rhopoint Components.

SRT CRB 1210-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1210-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 1210 range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.35W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 3/single cut), all in a small 1210 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1210-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1210 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.35W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 3/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1210-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1210-HT appeared first on Rhopoint Components.

SRT CRB 1206-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1206-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 1206 range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.25W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 2/single cut), all in a small 1206 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1206-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1206 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.25W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 2/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1206-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1206-HT appeared first on Rhopoint Components.

SRT CRB 0805-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 0805-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 0805 range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.125W and voltage rating of 100V trimmed or 300V untrimmed (trimming ratios 1.5/single cut), all in a small 0805 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 0805-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
0805 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.125W at +70°C
Voltage rating of 100V trimmed or 300V untrimmed (trimming ratios 1.5/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 0805-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
0805-HT appeared first on Rhopoint Components.

SRT CRB 0603-HT

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 0603-HT high temperature, non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers the same features as the CRB 0603 range, while allowing for high temperature applications of up to 300°C. The main features comprise of a resistance range from 1Ω up to 10MΩ, power rating of 0.1W and voltage rating of 75V trimmed or 220V untrimmed (trimming ratios 1.5/single cut), all in a small 0603 package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 0603-HT resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

High temperature trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
0603 package
Suitable for high temperature applications – operating temperature range of -55°C to +300°C
Power rating of 0.1W at +70°C
Voltage rating of 75V trimmed or 220V untrimmed (trimming ratios 1.5/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 0603-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
0603-HT appeared first on Rhopoint Components.

SRT CRB 1216H

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1216H trimmable chip resistor series from SRT Resistor Technology offers a resistance range from 1Ω up to 10MΩ, power rating of 0.4W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 8/single cut), all in a small 1216 surface mount package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1216H resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

Trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1216 package
Power rating of 0.4W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 8/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Temperature range from -55°C up to +155°C
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

The CRB trimmable non-magnetic resistor series is also available with an extended high temperature range version (up to +300°C). Please see the separate CRB-HT product pages for further information.

The below table gives full specifications for each resistor model available including the CRB 1216H series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1216H appeared first on Rhopoint Components.

SRT CRB 1216

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1216 non-magnetic trimmable chip resistor series from SRT Resistor Technology offers a resistance range from 1Ω up to 10MΩ, power rating of 0.4W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 4/single cut), all in a small 1216 surface mount package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1216 resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

Trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1216 package
Power rating of 0.4W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 4/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Temperature range from -55°C up to +155°C
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

The CRB trimmable non-magnetic resistor series is also available with an extended high temperature range version (up to +300°C). Please see the separate CRB-HT product pages for further information.

The below table gives full specifications for each resistor model available including the CRB 1216 series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1216 appeared first on Rhopoint Components.

SRT CRB 1210

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1210 non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers a resistance range from 1Ω up to 10MΩ, power rating of 0.35W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 3/single cut), all in a small 1210 surface mount package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1210 resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

Trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1210 package
Power rating of 0.35W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 3/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Temperature range from -55°C up to +155°C
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

The CRB trimmable non-magnetic resistor series is also available with an extended high temperature range version (up to +300°C). Please see the separate CRB-HT product pages for further information.

The below table gives full specifications for each resistor model available including the CRB 1210 series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1210 appeared first on Rhopoint Components.

SRT CRB 1206

Admin — Mon, 23 Nov 2020 20:42:39 +0000

The CRB 1206 non-magnetic, trimmable chip resistor series from SRT Resistor Technology offers a resistance range from 1Ω up to 10MΩ, power rating of 0.25W and voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 2/single cut), all in a small 1206 surface mount package. By utilising SRT’s thick film resistor technology, they are able to offer low tolerances down to ±5.0% and TCR as low as ±50 ppm/°C (between 10Ω and 10MΩ). The CRB 1206 resistor series is suitable for laser and air-abrasive trimming, and offers PtAg (Platinum-Silver), unpassivated contact areas suitable for soldering and conductive gluing. These resistors contain no organics, making them suitable for high vacuum applications.

Trimmable thick film chip resistor
Available in any resistance between 1Ω and 10MΩ
1206 package
Power rating of 0.25W at +70°C
Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 2/single cut)
Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
Temperature range from -55°C up to +155°C
Suitable for laser and air-abrasive trimming
High trimming ratios by special geometries
PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
Non-magnetic
No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

The CRB trimmable non-magnetic resistor series is also available with an extended high temperature range version (up to +300°C). Please see the separate CRB-HT product pages for further information.

The below table gives full specifications for each resistor model available including the CRB 1206 series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
1206 appeared first on Rhopoint Components.