• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 1216 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.4W at +70°C
• Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 8/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1216H-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

 

The post SRT CRB
1216H-HT appeared first on Rhopoint Components.

• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 1216 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.4W at +70°C
• Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 4/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1216-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

 

The post SRT CRB
1216-HT appeared first on Rhopoint Components.

• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 1210 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.35W at +70°C
• Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 3/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1210-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

 

The post SRT CRB
1210-HT appeared first on Rhopoint Components.

• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 1206 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.25W at +70°C
• Voltage rating of 200V trimmed or 600V untrimmed (trimming ratios 2/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 1206-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

 

The post SRT CRB
1206-HT appeared first on Rhopoint Components.

• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 0805 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.125W at +70°C
• Voltage rating of 100V trimmed or 300V untrimmed (trimming ratios 1.5/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 0805-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

 

The post SRT CRB
0805-HT appeared first on Rhopoint Components.

• High temperature trimmable thick film chip resistor
• Available in any resistance between 1Ω and 10MΩ
• 0603 package
• Suitable for high temperature applications – operating temperature range of -55°C to +300°C
• Power rating of 0.1W at +70°C
• Voltage rating of 75V trimmed or 220V untrimmed (trimming ratios 1.5/single cut)
• Tolerances as low as ±5.0% over the resistance range of 10Ω up to 10MΩ
• TCR as low as ±50 ppm/°C over the resistance range of 10Ω to 10MΩ
• Suitable for laser and air-abrasive trimming
• High trimming ratios by special geometries
• PtAg (Platinum-Silver), unpassivated contact areas for soldering and conductive gluing
• Non-magnetic
• No organics

Non-symmetric tolerances are also available (e.g. -0/+20%), please contact us for more information.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CRB 0603-HT series starts from ±5%, whereas the below table gives the full specifications of the standard CRB series:

¹⁾ Detailed information on request
²⁾ TC50: Temperature range +25°C…+85°C; TK50 not in the resistance range<100R
³⁾Continuous operating voltage U=√(P*R)

The post SRT CRB
0603-HT appeared first on Rhopoint Components.

• High temperature, meander structured surface-mount thick film chip resistor
• Available in any resistance between 100kΩ and 1TΩ
• 2010 package
• Power rating of 0.5W at +70°C
• Voltage rating of 1500V trimmed or 2000V untrimmed (tolerances ≥5%)
• Tolerances as low as ±1% over the resistance range of 100kΩ up to 1GΩ
• TCR as low as ±25 ppm/°C over the resistance range of 100kΩ to 10GΩ
• VCR as low as ±25 ppm/V over the resistance range of 100kΩ up to 100MΩ
• Temperature range from -55°C up to +300°C
• Non-magnetic
• PtAg (platinum silver) terminations for conductive gluing and soldering
• Low temperature and voltage dependency
• No organics

Custom tolerance, TCR and VCR options are available upon request. Please contact us for further information and availability.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CHM 2010-HT series starts from ±1%, whereas the below table gives full specifications of the standard CHM series:

¹⁾ At continuous power dissipation the dimensions of solder-pads have to secure a sufficient heat removal
²⁾ TCR: in ppm/K; +25°C…+125°C; TCR lower than standard TCR (highest value) or value >100G: +25°C…+85°C
³⁾ VCR: typical values, all negative, not for all TCR values available

The post SRT CHM
2010-HT appeared first on Rhopoint Components.

• High temperature, meander structured surface-mount thick film chip resistor
• Available in any resistance between 100kΩ and 1TΩ
• 0805 package
• Power rating of 0.125W at +70°C
• Voltage rating of 200V trimmed or 400V untrimmed (tolerances ≥5%)
• Tolerances as low as ±2% over the resistance range of 100kΩ up to 100MΩ
• TCR as low as ±25 ppm/°C over the resistance range of 100kΩ to 100MΩ
• VCR as low as ±100 ppm/V over the resistance range of 100kΩ up to 100MΩ
• Temperature range from -55°C up to +300°C
• Non-magnetic
• PtAg (platinum silver) terminations for conductive gluing and soldering
• Low temperature and voltage dependency
• No organics

Custom tolerance, TCR and VCR options are available upon request. Please contact us for further information and availability.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CHM 0805-HT series starts from ±2%, whereas the below table gives the full specifications of the standard CHM series:

¹⁾ At continuous power dissipation the dimensions of solder-pads have to secure a sufficient heat removal
²⁾ TCR: in ppm/K; +25°C…+125°C; TCR lower than standard TCR (highest value) or value >100G: +25°C…+85°C
³⁾ VCR: typical values, all negative, not for all TCR values available

The post SRT CHM
0805-HT appeared first on Rhopoint Components.

• High temperature, meander structured surface-mount thick film chip resistor
• Available in any resistance between 100kΩ and 1TΩ
• 1206 package
• Power rating of 0.25W at +70°C
• Voltage rating of 600V trimmed or 1000V untrimmed (tolerances ≥5%)
• Tolerances as low as ±1% over the resistance range of 100kΩ up to 100MΩ
• TCR as low as ±25 ppm/°C over the resistance range of 100kΩ to 100MΩ
• VCR as low as ±100 ppm/V over the resistance range of 100kΩ up to 100MΩ
• Temperature range from -55°C up to +300°C
• Non-magnetic
• PtAg (platinum silver) terminations for conductive gluing and soldering
• Low temperature and voltage dependency
• No organics

Custom tolerance, TCR and VCR options are available upon request. Please contact us for further information and availability.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CHM 1206-HT starts from ±1%, whereas the below table gives full specifications of the standard CHM series:

¹⁾ At continuous power dissipation the dimensions of solder-pads have to secure a sufficient heat removal
²⁾ TCR: in ppm/K; +25°C…+125°C; TCR lower than standard TCR (highest value) or value >100G: +25°C…+85°C
³⁾ VCR: typical values, all negative, not for all TCR values available

The post SRT CHM
1206-HT appeared first on Rhopoint Components.

• High temperature meander structured surface-mount thick film chip resistor
• Available in any resistance between 100kΩ and 1TΩ
• 1210 package
• Power rating of 0.35W at +70°C
• Voltage rating of 800V trimmed or 1200V untrimmed (tolerances ≥5%)
• Tolerances as low as ±1% over the resistance range of 100kΩ up to 1GΩ
• TCR as low as ±25 ppm/°C over the resistance range of 100kΩ to 10GΩ
• VCR as low as ±50 ppm/V over the resistance range of 100kΩ up to 1GΩ
• Temperature range from -55°C up to +300°C
• Non-magnetic
• PtAg (platinum silver) terminations for conductive gluing and soldering
• Low temperature and voltage dependency
• No organics

Custom tolerance, TCR and VCR options are available upon request. Please contact us for further information and availability.

Please see the derating curve below for the CHx-HT, CRB-HT and CBW-HT series from 0°C to +300°C:

The final measuring of the resistors takes place at room temperature (independent of TCR).

Please pay attention to the interconnection technology at high temperature applications.

Please note, the tolerance for the CHM 1210-HT series starts from ±1%, whereas the below table gives full specifications of the standard CHM series:

¹⁾ At continuous power dissipation the dimensions of solder-pads have to secure a sufficient heat removal
²⁾ TCR: in ppm/K; +25°C…+125°C; TCR lower than standard TCR (highest value) or value >100G: +25°C…+85°C
³⁾ VCR: typical values, all negative, not for all TCR values available

The post SRT CHM
1210-HT appeared first on Rhopoint Components.