DC Correct Digital Isolators - Rhopoint Components

NVE IL521-3E

Admin — Mon, 23 Nov 2020 20:53:30 +0000

The IL521-3E DC-correct dual channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL521-3E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 50kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Multidirectional two channel isolation
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
8-pin SOIC package

The IL521 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL521 series DC-correct two channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL521 DC-correct two channel digital isolator series including the IL521-3E:

The post NVE IL521-3E appeared first on Rhopoint Components.

NVE IL510-1E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL510-1E DC-correct single channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL510-1E from NVE have a pulse width distortion of 10ns with an isolation of 1KV_RMS and a transient immunity of 20kV/microsecond, the
internal clocking ensures a determined power-up state (“DC correct).

Surface-mount DC-correct single channel digital isolator
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
8-pin MSOP package

The IL510 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL510 series DC-correct single channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL510 DC-correct single channel digital isolator series including the IL510-1E:

The post NVE IL510-1E appeared first on Rhopoint Components.

NVE IL510-3E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL510-3E DC-correct single channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL510-3E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 20kV/microsecond, the
internal clocking ensures a determined power-up state (“DC correct).

Surface-mount DC-correct single channel digital isolator
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
8-pin SOIC package

The NVE IL510 series DC-correct single channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL510 DC-correct single channel digital isolator series including the IL510-3E:

The post NVE IL510-3E appeared first on Rhopoint Components.

NVE IL511-1E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL511-1E DC-correct dual channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL511-1E from NVE have a pulse width distortion of 10ns with an isolation of 1KV_RMS and a transient immunity of 50kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Unidirectional two channel isolation
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
8-pin MSOP package

The IL511 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL511 series DC-correct two channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL511 DC-correct two channel digital isolator series including the IL511-1E:

The post NVE IL511-1E appeared first on Rhopoint Components.

NVE IL511-3E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL511-3E DC-correct dual channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL511-3E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 50kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Unidirectional two channel isolation
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
8-pin SOIC package

The NVE IL511 series DC-correct two channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL511 DC-correct two channel digital isolator series including the IL511-3E:

The post NVE IL511-3E appeared first on Rhopoint Components.

NVE IL514-3E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL514-3E DC-correct multi channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL511-3E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 50kV/microsecond. Internal clocking ensures a determined power-up state (“DC correct) and ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Multi Channel isolation (2 transmit and 1 receive)
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
16-pin narrow 0.15″ wide SOIC package

The NVE IL511 series DC-correct multi channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL514 DC-correct multi channel digital isolator series including the IL514-3E:

The post NVE IL514-3E appeared first on Rhopoint Components.

NVE IL514E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL514E DC-correct dual channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL511-1E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 20kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Multi channel isolation (2 transmit and 1 receive)
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
16-pin 0.3″ wide SOIC package

The IL514 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL514 series DC-correct two channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL514 DC-correct two channel digital isolator series including the IL514E:

The post NVE IL514E appeared first on Rhopoint Components.

NVE IL515E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL515E DC-correct four channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL515E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 20kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Unidirectional four channel isolation
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
16-pin 0.3″ wide SOIC package

The IL515 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL515 series DC-correct four channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL515 DC-correct two channel digital isolator series including the IL515E:

The post NVE IL515E appeared first on Rhopoint Components.

NVE IL516-3E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL516-3E DC-correct four channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL516-3E from NVE have a pulse width distortion of 10ns with an isolation of 2.5KV_RMS and a transient immunity of 20kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Multidirectional four channel isolation
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
16-pin 0.15″ wide SOIC package

The IL516 isolators can be used with Power on Reset (POR) circuits common in microcontroller applications, as the means of ensuring the output of the device is in the same state as the input a short time after power up.

The NVE IL516 series DC-correct four channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL516 DC-correct two channel digital isolator series including the IL516-3E:

The post NVE IL516-3E appeared first on Rhopoint Components.

NVE IL516E

Admin — Mon, 23 Nov 2020 20:32:22 +0000

The IL516E DC-correct four channel digital isolators from NVE are a low-cost isolator alternative to opto-couplers, operating up to 2 Mbps over an operating temperature range of −40ºC to 85ºC. These devices use NVE’s patented IsoLoop® spintronic Giant Magnetoresistive (GMR) technology. A unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. The IL516E from NVE have a pulse width distortion of 10ns with an isolation of 2.5kV_RMS and a transient immunity of 20kV/microsecond, internal refresh clock which ensures the synchronisation of input and output within 9 μs of the supply passing the 1.5 V threshold.

Surface-mount DC-correct digital isolator
Multidirectional four channel isolation (2 transmit and 2 receive)
Power supply between 3V and 5V
Maximum speed of 2Mbps
Typical quiescent current of 0.0013A/channel
High voltage endurance of 1000V_RMS/1500V_DC
Temperature range of −40°C to +85°C
Common mode transient immunity of 30 kV/μs min. and 50 kV/μs typ.
Low EMC footprint
Pulse width distortion of 10ns
Propagation delay of 25ns
Barrier life of 44000 years
UL 1577 recognised; IEC 60747-5-5 (VDE 0884) certified
16-pin 0.3″ wide SOIC package

The NVE IL516 series DC-correct four channel digital isolators are ideal for the following applications

ADC’s and DAC’s
Digital filedbus
Multiplexed data transmission
Data interfaces
Board to board communication
Digital noise reduction
Ground loop elimination
Parallel bus
Peripheral interfaces
Logic level shifting

The below table gives the recommended operating conditions of the NVE IL516 DC-correct two channel digital isolator series including the IL516E:

The post NVE IL516E appeared first on Rhopoint Components.